There are not many sheds like the Mammoth Shed around. It’s extremely solid and sturdy.

• 0.6mm corrugated plate sheeting
• 1.2mm steel frame
• 1.2mm internal floor frame
• 1.2mm steel door
• 2mm triangular corner plate base
• 2mm door entry ramp (this is powder coated)
• Roof Supports:
  • Vertical roof supports: 1.2mm
  • Horizontal roof supports: 2mm
• 2mm Polycarbonate window
• Stainless steel bolts, tracks and pulleys
• 1mm anti-condensation felt across walls and doors. This is 110g per m². This is grey in colour.

The 12ft x 10ft Mammoth Shed has:

• A complete internal anti-con lining on the roof and walls
• Four build in vents (2 at either end)
• Handless Double sliding doors with precut holes to accommodate a long nose padlock 
• Floor support frame
• CE approved
• Preassembled window
• Gloves & Nut Setter included which is required for assembly
• Corner Anchor plate included 
• Door access height 5ft 9”
• Rubber door stops

The Window can be put on either side of the shed. You make the choice of where you want it to be at the time of assembly and adjust your build accordingly. As the window is part of the side walls, so it cannot be added to the back wall.

The 12ft x 10ft Mammoth shed is measured externally from the base from. These measurements are:

• Apex: 2180mm / 7′ 2″
• Eaves: 1870cm / 6′ 2″
• Door height: 1820mm / 6′ 0″
• Door opening: 1737mm / 5’8The imperial measurements are rounded to the nearest whole number

The Mammoth Shed is complete with an anti-condensation lining on both the internal walls and roof, as seen in the image below. It also has built in air vents to allow air-flow throughout the shed, which are both incredible ways to combat condensation in the Irish climate. The Mammoth shed is uniquely equipped to combat condensation and damp. Ireland has after all, essentially a temperate rainforest climate and buildings are liable to condensation during the months with changeable weather.

We also recommend that you:

• Incorporate a damp-proof membrane into your base
• You regularly air out your shed
• and that you do not put white goods into any steel shed

You will have zero issues with condensation if these steps are followed. 

The RAL Colour for this shed is Ral 7035, also known as Light Grey.

The Doors, Apex, Window frame, Trims are RAL 7016 (Anthracite Grey)

The Mammoth Shed comes with an 7-year rust perforation warranty.

These sheds are delivered in seven boxes.

These are generally too large for most personal vehicles, so if you are collecting this shed from us, we recommend that you come with a large flatbed truck.

First off, self-assembly is not for everyone. If you struggle keeping your cool with an Ikea product, we can safely say that this is not the product for you to assemble. You will require at least four able-bodied people, a calm day, the appropriate tools and to plan ahead to make this Mammoth shed correctly and efficiently.

Please note that self-assembly is not for everyone and we do not recommend that you even attempt it unless you have sufficient experience with large flat-packed builds and understand these type of instructions.

Flat-packed assembly tips for the Mammoth

• As with all steel sheds, a solid, level base is needed to assemble this shed onto. Concrete, pacing slabs, hardcore stone, our ShedBase etc.
• Squaring out the base is vitally important. If you do not square out the base correctly as per the instructions, you will struggle – and it may be impossible to make the rest of the shed. Do no proceed until your base is squared out.
• In the instructions it is noted that you place w2-29, in order: 1-26. This is very, very important. Start with 1 and work sequentially up to 26; Do not jump ahead. If you go out of sequence, you will run into all manner of issues further down the line.
• Some panels may appear ‘scratched’ or ‘scorched’. However these have a plastic wrap covering them (which protects the sheets in transit). Once this wrap is removed, these marks should instantly disappear.
• The panel number is at the top of the sheet.

DO NOT ASSEMBLE THIS SHED ON A DAY WITH HIGH-WINDS

Our Team can assemble the Mammoth shed for you if you do not wish to attempt it yourself. It generally takes them about 2 hours from start to finish. Use the dropdown menus to see the price of assembly in your county.

The team will assemble your shed for you provided that you have a suitable base (see below).
The assembly team do not apply the screw caps or remove the protective plastic film. These are optional and it is the customers’ choice to add/remove these if desired.

The assembly team do not assemble any other products other than the steel shed.
e.g. They do not assembly shelving units, canopies, carts or any other item purchased with the shed.

Please note: Shed assembly is weather permitting. High-winds or other averse weather conditions may lead to shed assembly cancellations. 

You will need a solid level base for this shed.

Appropriate bases include:

• Concrete
• Tarmac
• Paving Slabs
• Hardcore Stone

This shed cannot be built onto grass, muck, pallets, incomplete or uneven bases. For more information, read ‘Good Bases for Steel Sheds’